Boa Noite!
Galera!
Estou desenvolvendo um controlador de temperatura,
Quero que quando a temperatura de set seja selecionada tenha um delay
No acionamento do led no caso de 10s.
O problema é quando eu coloco o delay os botões do menu também demoram
os 10s para ser acionados, ou seja quando aperto o botão Up demora 10s para sub o Set.
Como posso fazer este delay sem interferir no loop dos botões?
Tags:
coloque o seu código aqui. Mas a principio, olhe na IDE o programa exemplo: Blink without delay
A saída é vc criar uma rotina sua de delay, para poder dentro dela continuar processando o que for necessário. Abaixo um exemplo que fiz em um projeto:
void myDelay(int millisecs)
{
int target=millis()+millisecs;
int i;
do
{
i=millis();
if ((i % 10) == 0)
processMessages();
} while (i <= target);
}
Esse rotina chama uma outra, processMessages(), de 10 em 10 milissecs, Dentro da processMessages vc pode testar as teclas, por exemplo.
Sacou?
Obrigado!
pela ajuda!
Cara mas não funcionou, eu pegue o menu base do site da engenheirando.
segue o link
http://engenheirando.com/arduino/displaylcd/
O menu que estou desenvolvendo e com base no menu dele!
não sei se não estou usando direito!
Se vc postar o seu código posso te ajudar melhor.
Pois é, sem o código fica complicado explicar.
Mas se o objetivo é efetuar um delay em um acionamento (um timmer por exemplo) sem interrupção ou sem travar a execução das demais funções do sistema, a solução é usar o Millis() como neste código exemplo da IDE.
/* Blink without Delay
Turns on and off a light emitting diode(LED) connected to a digital
pin, without using the delay() function. This means that other code
can run at the same time without being interrupted by the LED code.
The circuit:
* LED attached from pin 13 to ground.
* Note: on most Arduinos, there is already an LED on the board
that's attached to pin 13, so no hardware is needed for this example.
created 2005
by David A. Mellis
modified 8 Feb 2010
by Paul Stoffregen
This example code is in the public domain.
http://www.arduino.cc/en/Tutorial/BlinkWithoutDelay
*/
// constants won't change. Used here to
// set pin numbers:
const int ledPin = 13; // the number of the LED pin
// Variables will change:
int ledState = LOW; // ledState used to set the LED
long previousMillis = 0; // will store last time LED was updated
// the follow variables is a long because the time, measured in miliseconds,
// will quickly become a bigger number than can be stored in an int.
long interval = 1000; // interval at which to blink (milliseconds)
void setup() {
// set the digital pin as output:
pinMode(ledPin, OUTPUT);
}
void loop()
{
// here is where you'd put code that needs to be running all the time.
// check to see if it's time to blink the LED; that is, if the
// difference between the current time and last time you blinked
// the LED is bigger than the interval at which you want to
// blink the LED.
unsigned long currentMillis = millis();
if(currentMillis - previousMillis > interval) {
// save the last time you blinked the LED
previousMillis = currentMillis;
// if the LED is off turn it on and vice-versa:
if (ledState == LOW)
ledState = HIGH;
else
ledState = LOW;
// set the LED with the ledState of the variable:
digitalWrite(ledPin, ledState);
}
}
Jonatas obrigado pela dica consegui!!!
Elton, experimenta a função millis(), voce pode pegar como exemplo o blinkwithoudelay.
Abracos!
Obrigado!
Pela dica!
O Jonatas tinha me dado a dica mas só agora consegui!
Valeu!!!
abç!
Bem-vindo a
Laboratorio de Garagem (arduino, eletrônica, robotica, hacking)
© 2024 Criado por Marcelo Rodrigues. Ativado por